观利工业科技(上海)有限公司

合作品牌

  • AkzoNobel  International Paint 阿克苏诺贝尔国际牌油漆
  • PPG SIGMAKALON & AMERCOAT 庞贝捷 式玛卡龙 亚美隆 涂料
  • JOTUN 佐敦油漆
  • HEMPEL 海虹老人油漆
  • CMP 中涂涂料
  • AkzoNobel  International Paint 阿克苏诺贝尔国际牌油漆
  • PPG SIGMAKALON & AMERCOAT 庞贝捷 式玛卡龙 亚美隆 涂料
  • JOTUN 佐敦油漆
  • HEMPEL 海虹老人油漆
  • CMP 中涂涂料

AkzoNobel  International Paint 阿克苏诺贝尔国际牌油漆

聚氨酯清漆 Interthane 976

产品描述

Akzonobel International Paint 阿克苏诺贝尔国际牌油漆聚氨酯清漆 Interthane 976


A two component, fast drying, acrylic polyurethane clear finish giving excellent durability and long

term recoatability.

PRODUCT

DESCRIPTION

Suitable for use both in new construction and as a maintenance finish which can be used in a wide

variety of environments including offshore structures, petrochemicals plants, bridges and in the

power industry. Also used for OEM finishes, like pump, motor cases, etc.

INTENDED USES

Colourless

Gloss

40%

15-30 microns (0.6-1.2 mils) dry equivalent to

38-75 microns (1.5-3 mils) wet

16 m²/litre at 25 microns d.f.t and stated volume solids

642 sq.ft/US gallon at 1 mils d.f.t and stated volume solids

Allow appropriate loss factors

Air spray, Brush, Roller

PRACTICAL

INFORMATION FOR

INTERTHANE 976

Colour

Gloss Level

Volume Solids

Typical Thickness

Theoretical Coverage

Practical Coverage

Method of Application

Drying Time

Temperature Touch Dry Hard Dry Minimum Maximum

¹ See International Protective Coatings Definitions and Abbreviations

Overcoating Interval with

recommended topcoats

15°C (59°F) 7 hours 20 hours 24 hours Extended¹

25°C (77°F) 4 hours 14 hours 16 hours Extended¹

40°C (104°F) 3 hours 10 hours 12 hours Extended¹

Part A 34°C (93°F); Part B 49°C (120°F); Mixed 36°C (97°F)

0.97 kg/l (8.1 lb/gal)

REGULATORY DATA Flash Point (Typical)

Product Weight

VOC

See Product Characteristics section for further details

4.37 lb/gal (524 g/lt) EPA Method 24

Interthane® 976

Polyurethane

Page 1 of 4

Ref:2480

Issue Date:05/02/2015

Protective Coatings

Interthane® 976

Polyurethane

All surfaces to be coated should be clean, dry and free from contamination.

Steel Substrates

Interthane 976 should always be applied over a recommended anti-corrosive coating scheme. The

primer surface should be dry and free from all contamination and Interthane 976 must be applied

within the overcoating intervals specified (consult the relevant product data sheet).

Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO

8501-1:2007) or SSPC-SP10, Abrasive Blasting, or SSPC-SP11, Power Tool Cleaning) and patch

primed prior to the application of Interthane 976.

SURFACE

PREPARATION

Material is supplied in two containers as a unit. Always mix a complete unit

in the proportions supplied. Once the unit has been mixed it must be used

within the working pot life specified.

(1) Agitate Base (Part A) with a power agitator.

(2) Combine entire contents of Curing Agent (Part B) with Base

(Part A) and mix thoroughly with power agitator.

4 part(s) : 1 part(s) by volume

Recommended Typically 15-30 microns (0.6-1.2 mils) can be

achieved

Recommended Typically 15-30 microns (0.6-1.2 mils) can be

achieved

International GTA713

International GTA713

Do not allow material to remain in hoses, gun or spray equipment.

Thoroughly flush all equipment with International GTA713. Once units of

paint have been mixed they should not be resealed and it is advised that

after prolonged stoppages work recommences with freshly mixed units.

Clean all equipment immediately after use with International GTA713. It is

good working practice to periodically flush out spray equipment during the

course of the working day. Frequency of cleaning will depend upon amount

sprayed, temperature and elapsed time, including any delays.

All surplus materials and empty containers should be disposed of in

accordance with appropriate regional regulations/legislation.

Do not thin more than allowed by local

environmental legislation.

Not recommended

Recommended Use suitable proprietary equipment

APPLICATION Mixing

Mix Ratio

Working Pot Life

Airless Spray

Air Spray

(Conventional)

Brush

Roller

Thinner

Cleaner

Work Stoppages

Clean Up

15°C (59°F) 25°C (77°F) 40°C (104°F)

3 hours 2 hours 1 hour

Page 2 of 4

Interthane® 976

Polyurethane

Level of sheen and surface finish are dependent on application method. Avoid using a mixture of

application methods whenever possible. Best results in terms of gloss and appearance will always

be obtained by conventional air spray application.

This product must only be thinned using the recommended International thinners. The use of

alternative thinners, particularly those containing alcohols, can severely affect the curing

mechanism of the coating.

When overcoating after weathering or ageing, ensure the coating is fully cleaned to remove all

surface contamination such as oil, grease, salt crystals and traffic fumes, before application of a

further coat of Interthane 976.

When applying Interthane 976 in confined spaces ensure adequate ventilation.

In line with good painting practice, application should not take place in conditions which are

deteriorating, e.g. dew point is falling or there is a risk of condensation forming. Condensation

occurring during or immediately after application may result in a matt finish and an inferior film.

When applying Interthane 976 in confined spaces ensure adequate ventilation.

Absolute measured adhesion of topcoats to aged Interthane 976 is less than that to fresh material,

however, it is adequate for the specified end use.

This product is not recommended for use in immersion conditions. When severe chemical or

solvent splashing is likely to occur contact International Protective Coatings for information

regarding suitability.

Note: VOC values are typical and are provided for guidance purpose only. These may be subject

to variation depending on factors such as differences in colour and normal manufacturing

tolerances.

PRODUCT

CHARACTERISTICS

Interthane 976 can be applied directly over the following approved products:

Interthane 870

Interthane 990

SYSTEMS

COMPATIBILITY

Page 3 of 4

Interthane® 976

Polyurethane

Rect Top

Rect

Bottom

D

et

ail

Top

• Definitions & Abbreviations

• Surface Preparation

• Paint Application

• Theoretical & Practical Coverage

Individual copies of these information sections are available upon request.

ADDITIONAL

INFORMATION

This product is intended for use only by professional applicators in industrial situations in

accordance with the advice given on this sheet, the Material Safety Data Sheet and the

container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS)

which International Protective Coatings has provided to its customers.

All work involving the application and use of this product should be performed in compliance with all

relevant national, Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and

fumes will be emitted which will require the use of appropriate personal protective equipment and

adequate local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult International Protective Coatings

for further advice.

SAFETY

PRECAUTIONS

PACK SIZE Unit Size Part A Part B

Vol Pack Vol Pack

For availability of other pack sizes, contact International Protective Coatings.

20 litre 16 litre 20 litre 4 litre 5 litre

SHIPPING WEIGHT

(TYPICAL)

Unit Size Part A Part B

20 litre 16.93 kg 4.58 kg

Shelf Life 12 months minimum at 25°C (77°F). Subject to re-inspection

thereafter. Store in dry, shaded conditions away from sources of

heat and ignition.

STORAGE

The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first

obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product

(whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the

use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the

maximum extent permitted by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by operation of

law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied and technical advice given are subject to

our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the

light of experience and our policy of continuous development. It is the user's responsibility to check with their local representative that this data sheet is current prior to using the product.

This Technical Data Sheet is available on our website at www.international-marine.com or www.international-pc.com, and should be the same as this document. Should there be any

discrepancies between this document and the version of the Technical Data Sheet that appears on the website, then the version on the website will take precedence.

Important Note

Copyright © AkzoNobel, 05/02/2015.

All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies.

Page 4 of 4